Products: Tie Rod & Ball Joint Boots

  • Repair torn and worn-out boots of suspension tie rod ends - without having to buy the entire and expensive tie rod!
  • Adds durability surpassing most OEM rubber boots.
  • Exclusive 5 point sealing action.
  • Choose from four sizes* and Round or Octagon styles.
  • Made of Energy's HYPER-FLEX™ performance polyurethane for added performance and durability.

At last it is possible to replace a damaged tie rod dust boot without having the expense of buying an entire new tie rod! (Typically when tie rods are worn, an entirely new tie rod end is need and the additional expense of a suspension alignment is required.)

These exclusively engineered Energy Suspension ® boots resist damage from rocks, sand, water, road salt, and oils better than many other O.E.M. rubber boots.

All boots have a 5 Point Sealing Action, which not only prevents loss of tie rod lubricant but also inhibits contamination (the major cause of rod wear)! Availalble in red or black color.

GIVE YOUR VEHICLE SUSPENSION ADDED DURABILITY!

Ball Joint Boots

  • Repair torn and worn-out ball joint boots without having to buy the entire ball joint just to get the boot.
  • Adds both durability and that custom look attention custom show car builders!
  • For selected vehicle models only*.
  • Made of Energy's HYPER-FLEX™ performance polyurethane for added performance and durability.

Finally, someone has made a replacement ball joint dust boot! No more expense/cost worries when the boot wears-out or is damaged either from installation or from day to day use. They resist damage from rocks, road salt, sand and water better than many rubber boots. Sets includes two upper and two lower boots. Available in red or black color.

LASTS LONGER, SEALS BETTER & LOOKS GREAT FOR SHOW VEHICLES!

* For applications- find your specific vehicle listings and check if these products are available for that vehicle.

Measurements

Made of HYPER-FLEX™ Performance Polyurethane.

(A) Seals tight at tapered shaft
(B) Sharp edge helps seal-in lubricant
(C) Inside radius of boot works with rod socket as a wiper
(D) Extra sealing lips
(E) Barrel shaped for a better fit

Ordering Examples:
If A measures .630" at the largest taper and B measures 1.400" at the top of the socket use-
PT# 9.13101R, round, red in color
PT# 9.13102G, octagon, black in color

Available Colors / Color Codes: G for black, R for red. Example: 9.13101R = Red

NOTE: The rod end must measure at least the minimum dimensions shown below or larger. Approximates will do because of the elasticity of the product. The boot will seal better when it stretches over a larger dimension tie rod.

In some cases you need to insert a thin, not sharp, object under the lip of the boot to pull over area "B" of the tie rod end. Remember, choose the part number (PT#) that has the dimensions closest to the vehicle tie rod, yet it must measure larger than the minimums in the diagram below.

For applications not listed the catalog specific vehicle listings- use chart below

Minimum O.D. Dimensions Dimension A Minimum O.D. Dimensions Dimension B Style Round Shape Style Octagon Shape
31/64" or .472" or 12mm 1 13/64" or 1.200" or 30.5mm 9.13103 9.13104
19/32" or .590" or 15mm 1 3/8" or 1.375" or 35mm 9.13101 9.13102
9/16" or .550" or 14mm 1 7/16" or 1.437" or 36.5mm 9.13105 9.13106
21/32" or .650" or 16.6mm 1 5/8" or 1.625" or 41.3mm 9.13119 9.13120

Packaged 2 per peg board card for resale and 12 and 50 per box for installers.

9.13101 9.13107 9.13113
9.13102 9.13108 9.13114
9.13103 9.13109 9.13115
9.13104 9.13110 9.13116
9.13105 9.13111 9.13117
9.13106 9.13112 9.13118
9.13119 9.13121 9.13123
9.13120 9.13122 9.13124